|
|
|
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This equipment has been tested and found to conform to the directives and standards for a Class A Information Technology Equipment TYPE and for the Commercial Light Industrial equipment class.
The VIP-802 "MegaView"™ Video Switches are available as a single, dual, triple and quad multi head, Integrated Video Switch with Remote Control, switching from one to up to four monitors between two PC's.
The "MegaView" system consists of the following components:
1. One - Video Switch Unit
2. One - VIP-210 Power Supply.
Note: The "MegaView" does not come with VGA extension cables. They may be ordered from Vetra separately (see Accessories ).
There are three main steps to connect the Video Switch:
1. Connect PC's to Switch unit:
Connect the Video outputs of the PC's to the Video Switch using 15 pin HDD15 male/female extension cables. Connect PC#1's video output to the backpanel connector of the Video Switch marked "TO PC1 MON". Connect PC#2's video output to the backpanel connector of the Switch marked "TO PC2 MON".
Connect PC#1’s Monitor A video output to the backpanel connector of the Video Switch marked “TO PC1 MON A”, and connect PC#1's Monitor B video output to the back panel connector of the Video Switch marked “TO PC1 MON B”. For the V3 and V4 series of MegaView connect PC#1's Monitors C and D video outputs to the back panel connectors of the Video Switch marked "PC 1 MON C" and "PC1 MON D". Repeat this step for PC#2.
2. Connect a Monitor(s) to the Switch:
Connect the VGA monitor to the 15-pin HDD connector on the backpanel of the Video Switch marked "MONITOR IN".
Connect the VGA Monitor A to the 15-pin HDD connector on the back panel of the Video Swicth marked "MONITOR A IN". Repeat this step for Monitors B, C, and D.
3. Connect the Power Supply to the Video Switch:
The Video Switch is powered by
an external wall plug-in supply the VIP-210 (+5Vdc 1A reg. 110
- 240 Vac 50 - 60 Hz).
First plug the power output plug of this external supply into
the mating jack on the backpanel of the Video Switch marked "+5VDC
IN", and only then plug the supply into a suitable AC power
source. Since the Video Switch has no separate power on/off switch,
it is recommended that the power supply be connected to an AC
power source that has a power on/off switch.
OPERATION
1. Power Up Sequence:
There is no separate power control for the video switch. The switch derives its power from an external power supply provided with the MegaView. Plug the power supply into the Power Jack marked “+5VDC IN” on the back panel of the Video Switch, note that the PWR ON indicator on the front panel comes on.
2. PC Selection:
a) Front Panel Selection:
b) Remote Control (available on all models):
SPECIFICATIONS
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Environmental Operating
Temp: 5
to 104 deg. F (-15 - 40 deg. C)
Storage
Temp: -4
to 122 deg. F (-20 - 50 deg. C)
Supported
Hardware Video Monitors: VGA,
SVGA
Maximum
Resolution: up to 1600 x 1200 to 75 Hz
MegaView is a trademark of Vetra Systems Corporation Copyright © 1999 - 2008 by Vetra Systems Corporation All Rights Reserved
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
275 Marcus Blvd. Ste-J, Hauppauge, NY 11788-2022 USA Toll Free 1.800.537.9296 Tel: 631.434.3185 Fax: 631.434.3516 e-mail: sales@vetra.com |